Descubre la mejor forma de instalar unas guías ocultas para cajones

Concealed guides, also known as box guides , are always the best solution when we want the project we are doing to be well finished and at the same time a clean project . In general, they are high-quality guides that offer a smooth and subtle drawer opening system using bearings. In addition, the great advantage of these guides is that they are not visible to the naked eye since they are installed in the lower part of the drawer, which makes any project an elegant interior design work .


Let's see the steps you must follow to install hidden guides in your drawers.


How to install hidden guides in your drawers step by step

1. Each hidden guide consists of two pieces : the guide and a plastic piece that will be fixed in each lower corner of the drawer, right at the bottom. The first thing you should do is place the two plastic pieces just below both corners and secure them using lag screws . The guide will then be attached to these pieces using a click system . The guides will also be removed by pressing the triggers shown in the image.

Plastic parts for concealed drawer guides

2. Once both pieces of plastic have been placed in the position indicated in the image above, you must make two openings at the bottom on each side of the drawer where the guide will pass through. Below is an image that shows what we mean. It is important that the gap is 1-3 mm wider than the extendable arm of the guide so that it fits without any problem.

    Rear gap of the drawer to pass the guide



    3. Now you must proceed to install the metal guide on the wall inside the cabinet . Always pay special attention to ensure that the two guides are installed at the same height and, if installing several drawers, leave enough distance for them to fit, taking into account that the front part will be higher and wider than the rest. The way to install the guides will be by means of lag screws .

      In the case of the image, the front of the drawer will be embedded in the cabinet and that is why the guide is not fixed flush with the edge but 15mm inwards.

      Fixing hidden guides in the furniture



      4. Next, you need to make a hole just above the gap made in step 2. All concealed guides have a raised tab on the back that acts as a stop so that the guide holds the drawer in place when opening and closing from the back.

        Hole in the back of the drawer to install hidden guides

         

        5. Once the hole in the back is made, there is only one thing left to do: place the drawer on top of the guides and slide it all the way back until it stops against the tab and the front part of the guides engages with the plastic piece that was installed in step #1.

          With this you should have the hidden guides ready to use and the drawer mounted in your wardrobe. If you want to start with your DIY projects, here is our catalogue of hidden guides for furniture .

          Concealed drawer guides

          Also, if you need an audiovisual guide, we leave you an explanatory video on how to install a hidden guide in your drawers as we have explained to you.

          Discover how to install hidden guides for your drawers in less than 3 minutes

          If you are not sure which guide you need for your drawers, check out this article on types of drawer guides :

          Types of drawer guides
          Guías de cajón

          Leave a comment

          All comments are moderated before being published

          Todas las guías para cajones

          Ver todo
          Juego de guías con rodamientos H35 de extracción total 500 de largoFull extension H35 bearing guide set 500 long
          Juego de guías H53 de extracción total 600 de largo carga 100kg con cierre silenciosoH53 full extension guide set 600 long load 100kg with silent closing
          Juego de guías con rodamientos H45 de extracción total 550 de largo con cierre silenciosoFull extension H45 bearing guide set 550 long with silent closing
          Par de guías correderas metálicas de 310x27mm extracción parcial con rodamientos
          2 guías negras con ruedas para cajón de 250x37mm de 18kg de resistencia
          2 guías marrones con ruedas para cajón de 600x37 resistencia 18kg